Precision-digital PD6200 User Manual Page 4
- Page / 108
- Table of contents
- TROUBLESHOOTING
- BOOKMARKS
Rated. / 5. Based on customer reviews
Model PD6200 Analog Input Rate/Totalizer Instruction Manual
4
Reset Menu (reset) ------------------------------------------------------------ 34
Control Menu (Contrl) -------------------------------------------------------- 34
Setting Up the Rate/Totalizer Meter (setup) --------------------------- 35
Setting the Input Signal (input) ------------------------------------------ 36
Setting the Totalizer Features (total) ---------------------------------- 36
Dual-Scale for Level Application ------------------------------------------ 37
Setting the Decimal Point (dEc pt) -------------------------------------- 38
Programming the Rate/Totalizer (prog) -------------------------------- 38
Multi-Point Calibration & Scaling -------------------------------------- 39
MeterView
®
Pro Software ----------------------------------------------- 39
Scaling the Meter (SCALE) ---------------------------------------------- 39
Time Base, Total Conversion Factor & Total Reset -------------- 42
Calibrating the Meter with External Source (Cal) ----------------- 43
Setting the Display Parameter & Intensity (dsplay) ----------------- 44
Display Setup Menu --------------------------------------------------------- 45
Character Set for Engineering Units Display (d unit) -------------- 46
Setting the Relay Operation (relay) ------------------------------------- 47
Relay Assignment (Assign) ----------------------------------------------- 48
Setting the Relay Action ---------------------------------------------------- 49
Programming Set and Reset Points ------------------------------------- 50
Setting Fail-Safe Operation ------------------------------------------------ 50
Programming Time Delay -------------------------------------------------- 50
Relay Action for Loss of 4-20 mA Input (Loop Break) --------------- 50
Relay and Alarm Operation Diagrams ----------------------------------- 51
High Alarm Operation (Set > Reset) ------------------------------------- 51
Low Alarm Operation (Set < Reset) -------------------------------------- 52
High Alarm with Fail-Safe Operation (Set > Reset) ------------------ 53
Low Alarm with Fail-Safe Operation (Set < Reset) ------------------- 54
Pump Alternation Control Operation ------------------------------------- 55
Rate Relay Sampling Operation ------------------------------------------ 56
Total Relay Sampling Operation ------------------------------------------ 56
Signal Loss or Loop Break Relay Operation --------------------------- 57
Time Delay Operation ------------------------------------------------------- 58
Relay Operation Details ------------------------------------------------------ 59
Overview ------------------------------------------------------------------------ 59
Relays Auto Initialization ---------------------------------------------------- 59
Fail-Safe Operation ---------------------------------------------------------- 59
Front Panel LEDs ------------------------------------------------------------- 60
Latching and Non-Latching Relay Operation -------------------------- 60
Non-Latching Relay (Auto) ------------------------------------------------- 61
Non-Latching Relay (A-nman) --------------------------------------------- 61
Latching Relay (LatcH) ----------------------------------------------------- 61
Latching Relay (Lt-Clr) ---------------------------------------------------- 62
- Instruction Manual 1
- Disclaimer 2
- Warning 2
- Limited Warranty 2
- Registered Trademarks 2
- Table of Contents 3
- Table of Figures 6
- INTRODUCTION 6
- ORDERING INFORMATION 7
- SPECIFICATIONS 8
- Process Input 9
- Rate/Totalizer 10
- RTU Serial Communications 13
- COMPLIANCE INFORMATION 14
- SAFETY INFORMATION 15
- INSTALLATION 16
- Mounting Dimensions 17
- MAIN BOARD 18
- Connections 19
- Connectors Labeling 20
- Power Connections 20
- Signal Connections 21
- Relay Connections 22
- Switching Inductive Loads 23
- 4-20 mA Output Connections 24
- RLY5 RLY6 RLY7 RLY8 25
- DI 1-4 DO 1-4 26
- 5 VDC GND 26
- SETUP AND PROGRAMMING 27
- Description LED Status 28
- Main Menu 33
- Increment Digit 34
- Error Message (Error) 41
- Setup menu 41
- Minimum Input Span 41
- 10 VDC 41
- The display 43
- Display Setup Menu 45
- Relay Assignment (Assign) 48
- Setting the Relay Action 49
- Setting Fail-Safe Operation 50
- Programming Time Delay 50
- Manual (latching) 52
- Automatic (non-latching) 52
- Time Delay Operation 58
- Relay Operation Details 59
- Front Panel LEDs 60
- Non-Latching Relay (Auto) 61
- Non-Latching Relay (A-nman) 61
- Latching Relay (LatcH) 61
- PDA1044 Digital I/O Module 62
- Pump Alternation Operation 63
- Setting Numer 67
- Setting Numeric 68
- Password 70
- Advanced Features Menu 71
- Noise Filter (filter) 75
- Noise Filter Bypass (bypass) 75
- Select Menu (SElEct) 77
- Number of 78
- Low-Flow Cutoff (CutofF) 80
- Tare (tare) 82
- PDA1200 Meter Copy Cable 85
- Display flashes 86
- METER OPERATION 87
- Maximum/Minimum Readings 88
- TROUBLESHOOTING 89
- 20.000 90
- reset diaG 90
- Troubleshooting Tips 95
- LIM6200_H 108
- SFT039 Ver 2.200 & up 108
Related products and manuals for Control panel Precision-digital PD6200
(96 pages)© 2020, manymanuals.com. All rights reserved. | 1.931 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals