Precision-digital PD6000 User Manual Page 4
- Page / 96
- Table of contents
- TROUBLESHOOTING
- BOOKMARKS
Rated. / 5. Based on customer reviews
Model PD6000 Analog Input Process Meter Instruction Manual
4
Reset Menu (reset) ------------------------------------------------------------ 31
Control Menu (Contrl) -------------------------------------------------------- 31
Setting Up the Meter (setup) ------------------------------------------------ 32
Setting the Input Signal (input) ------------------------------------------ 33
Setting the Decimal Point (dEc pt) -------------------------------------- 33
Setting the Display Parameter & Intensity (dsplay) ----------------- 34
Display Setup Menu --------------------------------------------------------- 35
Character Set for Engineering Units Display (d unit) -------------- 36
Programming the Meter (prog) --------------------------------------------- 37
Program Menu for Single Scale Process ------------------------------- 37
Program Menu for Dual-Scale Level Applications -------------------- 37
Multi-Point Calibration & Scaling ----------------------------------------- 38
MeterView Pro Software ---------------------------------------------------- 38
Scaling the Meter (SCALE) -------------------------------------------------- 39
Dual-Scale for Level Application ------------------------------------------ 40
Calibrating the Meter with External Source (Cal) -------------------- 42
Setting the Relay Operation (relay) ------------------------------------- 43
Setting the Relay Action ---------------------------------------------------- 45
Programming Set and Reset Points ------------------------------------- 46
Setting Fail-Safe Operation ------------------------------------------------ 46
Programming Time Delay -------------------------------------------------- 46
Relay Action for Loss of 4-20 mA Input (Loop Break) --------------- 46
Relay and Alarm Operation Diagrams ----------------------------------- 47
High Alarm Operation (Set > Reset) ------------------------------------- 47
Low Alarm Operation (Set < Reset) -------------------------------------- 48
High Alarm with Fail-Safe Operation (Set > Reset) ------------------ 49
Low Alarm with Fail-Safe Operation (Set < Reset) ------------------- 50
Pump Alternation Control Operation ------------------------------------- 51
Relay Sampling Operation ------------------------------------------------- 52
Signal Loss or Loop Break Relay Operation --------------------------- 53
Time Delay Operation ------------------------------------------------------- 54
Relay Operation Details ------------------------------------------------------ 55
Overview ------------------------------------------------------------------------ 55
Relays Auto Initialization ---------------------------------------------------- 55
Fail-Safe Operation ---------------------------------------------------------- 55
Front Panel LEDs ------------------------------------------------------------- 56
Latching and Non-Latching Relay Operation -------------------------- 56
Non-Latching Relay (Auto) ------------------------------------------------- 57
Non-Latching Relay (A-man) -------------------------------------------- 57
Latching Relay (LatcH) ----------------------------------------------------- 57
Latching Relay (Lt-Clr) ---------------------------------------------------- 58
- Instruction Manual 1
- Disclaimer 2
- Limited Warranty 2
- Registered Trademarks 2
- Table of Contents 3
- Table of Figures 6
- INTRODUCTION 6
- ORDERING INFORMATION 7
- SPECIFICATIONS 8
- Process Input 9
- RTU Serial Communications 11
- COMPLIANCE INFORMATION 13
- SAFETY INFORMATION 14
- INSTALLATION 15
- MAIN BOARD 16
- Connections 17
- Power Connections 18
- Connectors Labeling 18
- Warning! 18
- Signal Connections 19
- Relay Connections 20
- Switching Inductive Loads 21
- 4-20 mA Output Connections 22
- RLY5 RLY6 RLY7 RLY8 23
- NO C NO C NO C NO C 23
- DI 1-4 DO 1-4 24
- 5 VDC GND 24
- SETUP AND PROGRAMMING 25
- PV1 & PV2 scales 30
- Increment Digit 31
- Display Setup Menu 35
- prog sCale 37
- MeterView 38
- Pro Software 38
- Scaling the Meter (SCALE) 39
- SCALE), page 39 42
- Setting the Relay Action 45
- Setting Fail-Safe Operation 46
- Programming Time Delay 46
- Manual (latching) 47
- Automatic (non-latching) 47
- Relay Sampling Operation 52
- On (Go to alarm condition) 53
- Time Delay Operation 54
- Relay Operation Details 55
- Front Panel LEDs 56
- Non-Latching Relay (Auto) 57
- Non-Latching Relay (A-man) 57
- Latching Relay (LatcH) 57
- 12345678910 58
- Pump Alternation Operation 59
- Setting Numeric 63
- Password 65
- 20.000 66
- user ICAL Copy diaG 66
- Advanced 67
- Features 67
- Noise Filter (filter) 69
- Noise Filter Bypass (bypass) 69
- Select Menu (SElect) 71
- Square) 72
- Prog E) 72
- Linear) 72
- Low-Flow Cutoff (CutofF) 74
- ICAL) and press Enter 76
- C CAL) or voltage 76
- C lo). Apply the 77
- C Hi). Apply the 77
- Meter Copy Function (Copy) 79
- PDA1200 Meter Copy Cable 79
- CPY rC while being pro 80
- METER OPERATION 81
- Maximum/Minimum Readings 82
- TROUBLESHOOTING 83
- reset diaG 84
- Paramete 85
- Troubleshooting Tips 88
- MOUNTING DIMENSIONS 95
- LIM6000_E.doc 96
- SFT039 Ver 2.000 & up 96
Related products and manuals for Control panel Precision-digital PD6000
(104 pages)© 2020, manymanuals.com. All rights reserved. | 0.118 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals